NER Bogie Tank Passenger

From Infogalactic: the planetary knowledge core
Jump to: navigation, search
NER Bogie Tank Passenger
LNER Class G6
Type and origin
Power type Steam
Designer Edward Fletcher
Builder
  • Neilson & Co.
  • Hawthorn & Co.
  • NER, Gateshead
  • NER, Darlington
  • NER, York
Build date 1874–84
Total produced 124
Specifications
Configuration 0-4-4T
Driver diameter 5 ft 6 in (1.68 m)
Trailing dia 3 ft 4 in (1.02 m)
Wheelbase 21 ft 8 in (6.60 m)
Length 33 ft 8 in (10.26 m)
Fuel capacity 2 long tons (2.0 t)
Water cap 1,000 imp gal (4,500 L; 1,200 US gal)
Boiler 10 ft 7 in (3.23 m) length
4 ft 3 in (1.30 m) diameter
Boiler pressure 160 psi (1.1 MPa)
Firegrate area 12.8 sq ft (1.19 m2)
Heating surface 1,109 sq ft (103.0 m2)
 • Tubes 1,025 sq ft (95.2 m2) (205 x 1.75")
 • Firebox 84 sq ft (7.8 m2)
Cylinders 2
Cylinder size 17 in × 24 in (430 mm × 610 mm)
Performance figures
Tractive effort 13,101 lbf (58.28 kN)
Career
Operators North Eastern Railway
London & North Eastern Railway
Class LNER: G6
Withdrawn 1920-1929
Disposition

The North Eastern Railway (NER) Bogie Tank Passenger (BTP) locomotives were designed by Edward Fletcher in 1873. The locomotives were for hauling passenger services on branch lines. They had an 0-4-4 wheel layout and a total of 124 locomotives were built. They were designated G6 by the London and North Eastern Railway (LNER).[1]

Rebuilds

With the introduction of the NER Class O (LNER G5), BTP locomotives started to become redundant. Fifty of the redundant BTPs were rebuilt between 1899 and 1908 as NER Class 290 (later LNER Class J77) 0-6-0T locomotives.[2] In 1903, locomotive No. 957 was rebuilt as a 2-2-4T (later designated LNER Class X2) specifically for hauling an officer's saloon.[3] With the reduction in passenger services towards the end of World War I, many of the BTPs became redundant. In 1921, ten BTPs were rebuilt to create further NER Class 290 locomotives.

Steam autocars

Many class BTPs gained a further lease of life in the early 1900s by being converted to work the Steam Autocars (push–pull trains) then being introduced. A Steam Autocar consisted of a BTP with one or two coaches (in which case the engine was in the middle), the train was driven from a driving compartment in the leading coach, leaving the fireman on the footplate. The driver had control of the regulator and reverser by means of a mechanical connection running under the coach and connecting to the engine using a form of universal joints. The driver also had full (Westinghouse) brake control via a second air pipe connection to the engine. This high pressure air supply also worked a whistle mounted above the driving compartment. Finally there was speaking tube communication between the driver and fireman - although there is evidence that this was little used.

Steam autocars were gradually withdrawn as the LNER introduced Sentinel steam railcars. The coaches were converted back to normal coaches but the BTPs were withdrawn.

Withdrawal

Withdrawals of the G6 took place between 1920 and 1929 and none is preserved.

References

  1. Lua error in package.lua at line 80: module 'strict' not found.
  2. Lua error in package.lua at line 80: module 'strict' not found.
  3. Lua error in package.lua at line 80: module 'strict' not found.

<templatestyles src="Asbox/styles.css"></templatestyles>